- HOW TO DISASSEMBLE ITHACA MODEL 49 FOR NEW HAMMER HOW TO
- HOW TO DISASSEMBLE ITHACA MODEL 49 FOR NEW HAMMER FULL
- HOW TO DISASSEMBLE ITHACA MODEL 49 FOR NEW HAMMER OFFLINE
To keep the parts in place, it is best to do this entire process with the tool on its side. In some cases, if the problem lies in the gearbox or percussion mechanism, we additionally unscrew the end of the gearbox housing, and then carefully remove the casing made of plastic. To do this, unscrew the crepes located on the stator, then detach 4 terminals from the stator contacts. Removing the front part, for which you need to unscrew the 4 screws located near the drill.Removing the cover (rear) on the handle.Removing the switch handle, having previously placed the operating mode lever to the maximum position.Carefully take out the steel ball, which acts as a fixation.After that, we proceed to remove the drill coupling casing itself. Removing the rubber tip and ring spring.
HOW TO DISASSEMBLE ITHACA MODEL 49 FOR NEW HAMMER HOW TO
How to repair 11E Not vibrating change O ring To start repairing a perforator, including a barrel type, you must properly disassemble the device: It is important to be careful and careful when repairing a tool, then in 99% of cases the repair will be successful.! To prevent this from happening, you need not only to know how to properly repair a hammer drill, but also how to assemble it. the appearance of unnecessary parts after assembly will indicate repair miscalculations. The second operation in some cases is more difficult than the first. For more serious problems, you need to disassemble the hammer drill. If you make a thorough inspection of the parts of the instrument, it is not difficult to see other minor malfunctions that led to the breakdown of the device. The damaged wire on the device, like other minor mechanical damage, can be easily noticed. An elementary inspection is enough to understand that the tool has broken conditionally, that it can be easily repaired by yourself without outside help. Due to simple inattention, people pay significant money for a sheer trifle in puncher repair services. The most common cause of tool breakage is loose wire. To repair the device, you should study the components of the punch and learn how to disassemble and assemble it. For trouble-free operation for a long time, you should carefully monitor and care for the instrument. Begin to investigate the cause of the unit failure. At the same time, such noises were not noticed before.Īny of the above signs should not be ignored.
The appearance of extraneous noise when working with the device.The device does not turn on the first time or works intermittently.There are pauses or small short circuits during operation.Although not every man knows how to repair a hammer drill, it doesn’t matter! This article will help you do DIY repairs without assistance. Like any other technical device, a hammer drill can be repaired, for this it does not have to be carried to a specialized workshop. Therefore, each owner of this device should know how to repair a punch with his own hands. Due to such loads, even branded models are susceptible to breakdowns.
HOW TO DISASSEMBLE ITHACA MODEL 49 FOR NEW HAMMER FULL
As we know, the rock drill is often used at full power in the toughest conditions.
This is due to the high stress on the tool. In the latter case, it will not be superfluous to consult an experienced specialist.Ī hammer drill is an indispensable tool at any construction site, but due to careless use it wears out very quickly and fails. If the inspection of the unit did not reveal a breakdown, then it is necessary to postpone the repair of the hammer drill. If the device was purchased relatively recently, and the model itself is more modern and costs a lot of money, then it is best to contact the service center, because an independent repair can not only fix the device, but cause harm.
HOW TO DISASSEMBLE ITHACA MODEL 49 FOR NEW HAMMER OFFLINE
Feel free to start an offline repair if the cause of the tool malfunction is visible visually and you already have an idea of the perforator stuffing. If the device has served for many years and is not of significant value, you can try to find the cause of the breakdown by disassembling the tool into separate parts. In this case, the next step is to disassemble the punch. Not always, a visual inspection will help to identify the cause of the breakdown.
0 kommentar(er)
